Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.
|Published (Last):||9 March 2017|
|PDF File Size:||18.35 Mb|
|ePub File Size:||17.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Enter text from picture: To print the manual completely, please, download it. When Temperature Start, Bank 3 feature 13 is selected on, the temperature insallation mode can be activated from the transmitter.
Prestige APS-997C Installation Manual
The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. The following procedure must be performed after the installation nanual any Remote Start Device. Page 18 Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules.
Page 11 ground trigger output wire of motion detectors, microwave detectors, or installatioh break detectors, can be connected to this Light Green trigger input wire. The mounting location selected must be within 24″ Comments to this Manuals Your Name.
If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger. In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Enter text from picture: These modules are used to access a variety of features in the vehicle majual can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting.
Platinum APS-997C Installation Manual
Don’t show me this message again. You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you’ve made the changes you wanted in Bank 2, Siren two Long ChirpYou can also go right to bank 3 by: Connect this wire to the vehicle’s parking light feed wire. This is a normally opened starter cut arrangement, when power is removed from the security system, the starter disable feature will remain operational, and the installaton will not start.
Locate the control wire that connects the drivers door pin switch to the key in sensor switch.
Aps c Installation Manual
Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle. Once activated, the unit will start 1 time if the vehicle temperature reaches “0 ” and then will run the allotted time. Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay.
This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. Page 27 b 27 of Mechanical Neutral Start Switch from starting mznual gear.
Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. Page 7 when used and the neutral safety switch as shown in the following diagram.
Audiovox car security system installation manual 24 pages. Page 19 Monitoring The Vehicle’s Engine: Do not remove the fuse holders from this wire harness.
When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down. Starter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear. Page 29 b 29 of The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above the level it was before the vehicle began to crank which indicates the vehicle is running.
Got it, continue to print. Page 30 For technical support go to www. Page of 28 Go. Page 22 Mechanical Neutral Start Switch from starting in gear. Page 3 3 of For technical support go to www. Temperature Start Programming And Information. These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. This is a normally opened starter cut arrangement, when power is removed from the secu- rity system, the starter disable feature will remain operational, and the vehicle will not start.
PLATINUM APSC INSTALLATION MANUAL Pdf Download.
Page 26 The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. Page 24 To connect to the key in sensor circuit as shown for method 2: Page 12 21 Light Blue Wire: To achieve optimum performance the coil signals must be evenly distributed.
The following two circuits may be used only if the manuxl circuit is not available.